| | How do I set the ID code at the transmitter for the 5140 and 5132? | |
| | - Connect unit to power cord, and press and release on/off button to turn unit on. Red POWER light should be lit.
- With one or both of the loop wires disconnected ? press and hold the #5 button on the transmitter. The LOOP light blinks 9 times, release button ? you now have a new id code set in the transmitter.
- Connect the loop wire ? the LOOP light should light solid red showing a continuous boundary wire loop.
- Press any one of button 1.
- To set the boundary field width use the table listed inside the front door for reference.
| |
| |
| My collar does not seem to be working. What should I do?
| |
| | Adjust fit of collar Trim hair or use longer probes Recharge Batteries
| |
| |
| ◊ | Which probes should I use on my dog? | |
| | Use short probes for short haired dogs and longer probes for longer or thicker haired dogs.
| |
| |
| How do I set a new collar's stimulation level or check the current setting on the 5140 or 5132? | |
| | - With the unit turned on ? you can check the current stimulation level setting by quickly pushing the power button for less than 2 seconds. The light will come on, and then blink to signify the setting level.
- With the unit turned on ? you can reset the stimulation level at any time. Simply push and hold the power button until the light goes off ? then quickly push the button for the desired level (1 ? 5). The light will blink showing the level.
| |
| |
| ◊ | How many acres will my dog be confined using the 5140 and 5132? | |
| | Fence Free and Fence Free Deluxe can cover up to 25 acres
Additional wire and flags would need to be purchased separately-5147 Boundary Kit. | |
| |
| I have installed my wall unit for the 5140 or 5132 and there are no lights on. What could be wrong? | |
| | If there are no lights, the following may have occurred:
- One or both wires are not properly connected.
- Both wires are connected but the wire is broken or nicked.
- The transmitter has malfunctioned.
- The transmitter is not plugged in or turned on.
| |
| |
| How do I charge the collar for my 5140 or 5132? | |
| | - Ensure the power transformer is plugged in and the LED is on.
- Place collar receiver onto docking station located on the wall unit transmitter.
Initial charge will take up to 10 hours and all subsequent charges should take 2 or more hours to completely charge the battery. | |
| |
| How do I test the wire for my 5140 or 5132? | |
| | Turn on the wall mount transmitter/control box. Hook up the test light to collar and slowly walk the collar receiver toward the boundary wire, listen for the warning tone, and watch the test light illuminate.
| |
| |
| The collar for my 5140 or 5132 comes preset at Level 1. How do I change the correction level? | |
| | There are 5 available correction levels. To increase the correction level, press button for less than 2 seconds for the number of times for each correction level. For example, press 3 times for less than 2 seconds each time for Level 3 correction. Remember when training, always start at the lowest level and check your dogs response to the stimulus. You should always use the lowest level necessary to get the desired response.
| |
| |
| How long will training take for my 5140 or 5132? | |
| | Each step should take approximately three days to complete. Training will take 10-20 minutes, 2-4 times a day for 7-14 days.
| |
| |
| How long will the batteries last for the 5140 or 5132? | |
| | Under "normal" conditions a full charge will last 3 days, but we recommend placing the collar on the docking station ate the end of each day.
| |
| |
| It says that it is waterproof on my collar- what does that mean? | |
| | The collar can be submerged in water up to 10 feet.
| |
| |
| | | |
| | | |
| | | |
